Welcome, Guest. Please login or register.

Login with username, password and session length

Author Topic: Fitting Competizione pedals  (Read 6867 times)

Offline Pedro

  • Assetto Member
  • **
  • Posts: 53
  • Carlo Rating: 0
    • Inverkeithing, Fife
Fitting Competizione pedals
« on: May 04, 2015, 08:26:29 pm »
Fitted my pedals at the weekend. Found nothing online with regards to a fitting guide so just expected the pedals to go on like any other, which was a good assumption.

The normal pedals and their rubber boots just pull off.
Drill 6mm holes in the bare pedals, using the black plastic mounts which come with the Competizione pedals as guides.
Put the new pedals on with the nuts and bolts provided.
Jobs a good 'un.

Excuse the crud on the floor...


  • Advertisement
  • ***

    Offline WhizzBang

    • Esseesse Member
    • ***
    • Posts: 104
    • Carlo Rating: 0
      • Brough, East Yorkshire
    Re: Fitting Competizione pedals
    « Reply #1 on: May 05, 2015, 12:25:22 pm »
    Looks good, might have to consider a set of these
    2011 Abarth 500C Granito Lucente
    Magneti Marelli SS500R2 Bombardone
    GTT Induction Pack
    Tarox F2000 + RC5+ Pads

    Offline Kimusubi007

    • S2000 Member
    • *****
    • Posts: 1112
    • Carlo Rating: 2
      • Sydney, Australia
    Re: Fitting Competizione pedals
    « Reply #2 on: May 05, 2015, 12:49:30 pm »
    heaps better, looks much more race style    :thumb:
    Yes, kids and golf clubs do fit in an Abarth 500!!!

    Offline Corgikid

    • Esseesse Member
    • ***
    • Posts: 127
    • Carlo Rating: 0
      • Liverpool
    Re: Fitting Competizione pedals
    « Reply #3 on: September 14, 2015, 03:36:01 pm »
    I found this topic last week when I got the pedals for my car. Hope its ok to add some pictures to it showing the work involved. The new pedals come in two parts. The back part is a plastic plate that fits over the original and has pre drilled holes in in making the job of drilling them a breeze. Also in the kit is a small plastic cube. This slots into the rear bottom of the accelarator pedal so that the nut does not need a spanner on it when tightening. Make sure you have the plastic plates the right way up so the holes are not drilled incorrectly. Apart from that its an easy job and took no more than 10 minutes.
    Trofeo 595, BMC filter, Bluespark, Eibach Pro kit, Bilsteins, Team Heko Deflectors, M-Tech short shift.

    Offline AdamAbarth

    • S2000 Member
    • *****
    • Posts: 639
    • Carlo Rating: 4
      • Herts
    Re: Fitting Competizione pedals
    « Reply #4 on: September 14, 2015, 04:46:42 pm »
    Tidy job there Gary  8)
    A500 Euro 6

    Record Grey - 10 Spoke Diamond Alloys (now black) - BMC Filter - Eibach Pro Kit - Power Motive Valve Exhaust with Black Tips - Team Heko Deflectors - Carbon Mirror Caps - Smoked Indicators

    Offline fpan

    • S2000 Member
    • *****
    • Posts: 857
    • Carlo Rating: 3
    Re: Fitting Competizione pedals
    « Reply #5 on: April 08, 2016, 01:53:57 pm »
    They look good but aren't they more slippery to drive with wet shoes as compared with the originals?